V-Mach International

• Used for Grinding, Light Milling, Drilling & Inspection of Round & Square Jobs.
• Accuracy for Flatness, Squareness and Parallelism within 0.010mm up to 150W above that 0.020mm up to 200W.
• Hardness 60±3 Rc.
• Supplied in perfect matched pair.
• Supplied with clamp which can be used from both sides to suit job dimensions.
• Holds & Clamps the heavy jobs rigidly.
• Can also be used for end face, side face and right angle Grinding

• Used for Grinding, Light Milling, Drilling & Inspection of Round & Square Jobs.
• Accuracy as per IS - 2949 - 1974.
• Hardness 60±2 Rc.
• Supplied in perfect matched pair.
• End face grinding, square with sides is possible.
• Two 90° "V" angle for different capacities.
• Special sizes can also be manufactured.
• Supplied with Clamp.

• Used for Grinding, Light Milling, Drilling & Inspection of Round & Square Jobs.
• Accuracy for Flatness, Squareness and Parallelism within 0.010mm up to 150W above that 0.020mm up to 200W.
• Hardness 60±3 Rc.
• Supplied in perfect matched pair.
• Supplied with clamp which can be used from both sides to suit job dimensions.
• Holds & Clamps the heavy jobs rigidly.
• Can also be used for end face, side face and right angle Grinding

• Used for Grinding, Light Milling, Drilling & Inspection of Round & Square Jobs.
• Accuracy for Flatness, Squareness and Parallelism within 0.010mm.
• Can be used on its base, the ends & on either side.
• Hardness 60±2 Rc.
• M10 tapping at base M8 tapping on side for clamping on angle plate or face plate or on magnetic chuck.
• A clamp with cap & adjustable screws prevents tilting of block.
• A clearance hole at centre for drilling or removing of dowel pins.
• The "V" at stepped end at right angle to the base provides a handy means for holding shouldered studs, round pins etc.

Heavy Duty Fine Pitch Multi Coil Electro Magnetic Chucks ( Transverse Pole ) IS - 8710 - 1978 : Series UL - 715

• Work holding device for surface grinding machines.
• Each pole is having separate coil, so / hence very strong & even magnetic flux is generated.
• Accuracy as per IS : 8710 - 1978.
• Magnetic pull is 30-50 % more than IS specification.
• Fine Pitch 5mm makes it suitable to hold thin & small jobs.
• Mag - D - Mag with variable control unit allows to neutralize the residual magnetism precisely, using a microprocessor based control circuitry.
• Variable supply to vary power which helps in alignment & removing of warpages of thin jobs.
• Chuck is tested for Slippering force, Waterproof test, Temperature rise test, electrical & demagnetizing tests.
• Also available in Longitudinal Poles.

• Used for lifting & handling of steel plates, heavy block & castings as well as heavy round or cylindrical parts.
• The 1 : 3.5 or 1:3 time safety factor of the recommended load to the test load ensures use at optimal
• working conditions even with substantial air gaps & surface conditions. Compact design, strong magnetic pull, total work safety
• Easy operated lever for ON-OFF.
• Spring loaded block at side for safety feature.
• Suitable for Flat & Round jobs.
• No damage on job during operation.
• We Also Undertake Calibration with form No. 11 and Repairing of All Types of Permanent Magnetic Lifter

We are a leading entity, occupied in presenting a wide range of Round Magnetic Chuck. Furthermore, our customers can avail these products from us at reasonable prices.

• Work holding device on Cylindrical Grinding m/c to grind outer diameter & face component as bearing recess, flanges, collet bushes, discs etc.
• Can also be used on Lathe machine.
• Mag - D - Mag with variable control unit allows to neutralize the residual magnetism precisely.
• Magnetic Coil ( outer body ) remains stationary & middle part ( Round body ) will rotate with spindle through adaptor sleeve.
• Variable supply is useful to true the job.
• 4 T-slots for easy location of job.
• Chuck is tested for Slippering force, Temperature rise, Waterproof, Electrical & Demagnetizing tests.
• Battery Back-up unit is also available on request

• Used for Grinding, Light Milling, Drilling & Inspection of Round & Square Jobs.
• Accuracy for Parallelism is within 0.010mm.
• Provided with ON-OFF switch except for 25 x 25mm block.
• Supplied in perfect matched pair. Harden Strips provided in hard pair.

• Used for lifting & handling of steel plates, heavy block & castings as well as heavy round or cylindrical parts.
• The 1 : 3.5 or 1:3 time safety factor of the recommended load to the test load ensures use at optimal
• working conditions even with substantial air gaps & surface conditions. Compact design, strong magnetic pull, total work safety
• Easy operated lever for ON-OFF.
• Spring loaded block at side for safety feature.
• Suitable for Flat & Round jobs.
• No damage on job during operation.
• We Also Undertake Calibration with form No. 11 and Repairing of All Types of Permanent Magnetic Lifter

Features

• Electro Permanent Magnets for Handling in Vertical or Horizontal Position.
• EPM lifting magnet is designed with the consideration of all industrial safety knobs. Therefore they are very compact light weight high strength and very reliable and safe in use.
• Electro Perm Magnetic lifter is combination of permanent as well as electro magnet power which is required to clamp the job or declamp the job.
• Lifted plate will not fail down even when electric power fail because EPM LIFTER requires power only a for holding the plates and declamping the plates. So it is 100% safe for handling the plates.
• Continuous electricity is not required so it is having advantage of saving electricity over conventional electro magnetic Lifter.
• Electro permanent magnetic lifter is used with combination of various magnets. At fix structure with provision of chain. So this will help to handle plain as well as bend sheets in short it will take care of bendness of plates.
• Safety interlock key to magnetized / demagnetized. Two buttons are to be press simultaneously with help to avoid chance of accident.
• "Inching" feature - when the magnets is switch ON, it might lift more than a single plate. Inching operation reduces the magnetic power slowly such that additional plates, if lifted are dropped. This is used to make sure that only one plate is handled at a time.
• Lamp Block - Displays the systems present state. Spreader beam fitted with suspension systems / Control Panel / Indicative Tower lamp etc.

Application

• Ideal for handling single plate in stockyards.
• Most effective in ship building industry.
• It is use on flame cutting m/c. plasma cutting m/c and water jet cutting m/c.
• It is useful for handling small as well as large plates.
• EPM Lifter is design as per customer plate sizes.
• Controller is having special facility of selector switch help for lifting small size sheets and large plates.
• It is the EPM lifting system is very suitable with EOT / GANTRY / MOBILE crane etc.

Optional Units

• Radio Remote Control - Operates from a convenient distance all the function i.e. MAG / DEMAG / Inching.
• ADPREM - Accidental Demagnetization Prevention Mechanism. Disable the demagnetization cycle when carrying load.

Design

• Designing of EPM Plate Lifter Depends upon minimum and maximum size of plate ( length X weight X thickness ) Crane Capacity.
• Weight of Plates.

Features

• Used as a workpiece holding device for Squareness grinding inspection & light machining.
• Accuracy for Squareness & parallelism is within 0.005 mm.
Front is magnetic face.
• Hardened strips provided on all face except back of magnetic face for wear resistance.
• Operates on 24 VDC, controlled by Mag-D-Mag with variable control unit.
• Easy to operate.
• Saves time as mechanical clamps are avoided.
• DEMAG switch for easy removal of jobs.
• Battery back-up unit is also available on request.

• Compact design with very strong magnetic pull.
• Used For Lifting, Holding & Locating of ferous parts.
• tapped hole on rear of magnetic face for lifting arrangement.

• 16 x 18 H
• 22 x 20 H
• 27 x 25 H
• 35 X 30 H
• 50 X25 X25 H
• 70 X 25 X 25 H

• Used for grinding, light Milling, Drilling & inspection of round & square Jobs.
• Uniform and Strong magnetic pull to all three magnetic surfaces, Top, Bottom & V Faces.
• Easy ON - OFF facility.

• Suitable for drilling & light Machining.
• Easy to operate.
• Saves time as mechanical clamps are avoided.
• Economical for operation & maintenance.
• Powerful holding with the magnet.
• Vertical lifting force is 35 to 40 kg per cm sq.

• With fine adjustment
• Clamp Hole 3/8" Diameter with 8 mm sleeve
• For dial indicators with lug back or flat back
• Base: 60x50x55 mm (2.4x2x2.2") with on/off switch

Features

• EPM lifting magnet is designed with the consideration of all industrial safety knobs. Therefore they are very compact light weight high strength and very reliable and safe in use.
• Electro Perm Magnetic lifter is combination of permanent as well as electro magnet power which is required to clamp the job or declamp the job.
• Lifted plate will not fall down even electric power failed because EPM LIFTER requires power only for holding the plates and declamping the plates. So it is 100% safe for handling the plates.
• Continuous electricity is not required so it having advantage of saving electricity over conventional electro magnetic Lifter.
• Electro permanent magnetic lifter is used with combination of various magnets. At fix structure with provision of chain. So this will help to handle plain as well as bend sheets in short it will take care of bendness of plates. Safety interlock key to magnetized / demagnetized. Two buttons are to be press simultaneously with help to avoid chance of accident.
• "Inching" feature - when the magnets is switch ON, it might lift more than a single plate. Inching operation reduces the magnetic power slowly such that additional plates, if lifted are dropped. This is used to make sure that only one plate is handled at time.
• Lamp Block - Displays the systems present state.

Application

• Ideal for handling single plate in stockyards.
• Most effective in the ship building industry.
• It is use on flame cutting m/c. plasma cutting m/c and water jet cutting m/c.
• It is useful for handling small as well as large plates.
• EPM Lifter is design as per customer plate sizes.
• Controller is having special facility of selector switch help for lifting small size sheets and large plates.
• It is the EPM lifting system is very suitable with EOT / GANTRY / MOBILE crane etc.

Optional Units

• Radio Remote Control - Operates from a convenient distance all the function i.e. MAG / DEMAG / Inching.
• ADPREM - Accidental Demagnetization Prevention Mechanism. Disable the demagnetization cycle when carrying load.

Design

• Designing of EPM Plate Lifter Depends upon minimum and maximum size of plate ( length X weight X thickness )
• Crane Capacity.
• Weight of Plates

Features

• Electro Magnetic Lifter is design with the consideration of all Industrial safety knob, therefore they are very compact, light weight, high strength & very reliable safe in use.
• Electro Magnetic Lifter are work on Electricity & require 220V or 415V supply.
• Electro Magnetic Lifter is used with combination of various magnets. At fixed structure with provision of chain. So this will help to handle plain as well as bend sheet, In short it will take care of bendness of sheet
• Inching feature or variable power knob is provided, It ensures that single plate will be lifted.
• Lamp block – Displays the system presents.

Application

• It is use on flame cutting machine, plasma cutting machine and water jet cutting machine.
• It is useful for handling small as well as large plates.
• Controller is having opetional facility of battery back up which helps to keep magnet on for 15 minutes.

Design

• Designing of Electro Magnetic Plate Lifter Depends upon minimum and maximum size of plate ( length X weight X thickness )
• Crane Capacity.
• Weight of Plates.

All Sides Are Hardened & Ground.

• Used for grinding, light Milling, Drilling & inspection of round & square Jobs.
• Uniform and Strong magnetic pull to all three magnetic surfaces, Top, Bottom & V Faces.
• Easy ON - OFF facility.

Comparison between Ultra brand Hardened V Block and other brand Hardened V Block

Due to All sides hardened you will get 40% better life as compared to with ordinary blade and bit pasted hardened V blocks & Double the life than Soft V Blocks.

• Used for Precision measurement,setting of angles & Light machining.
• Accuracy for Square ness, Flatness & Parallelism within 0.010mm upto 200L & 0.015mm upto 450L.
• Angle can be set within ±5 seconds.
• Centre Distance between roller is within 0.005mm.
• Made from high quality alloy steel Hardness 60 ± 2 Rc & Tempered.
• Magnetic Table for job holding.
• Firm hinged clamp to reduce possibility of distortion.
• Magnetic Chuck with fine Pitch. ( 1.5mm )

• Used for removing or collecting fine ferrous or ferromagnetic contaminants from oil tank or coolant tank.
• Powerful magnet allows large collection of particles.
• Stainless steel body for rust prevention.
• Handle or eye bolt on top for easy handling.
• Available in different diameters & lengths.