V-Mach International

Features

• Tungsten Carbide Tip brazed in front for high wear resistance.
• Shank made from Alloy Steel 20MnCr5 and case hardened for 50-53 HRc.
• Precision ground. Tip runout within 0.015 mm w.r.t. Taper.
• Standard Point Angle 60°
• Broadly confirms to IS : 2534 - 1963 (Equivalent to DIN : 806-807).

Additional Information:

• Delivery Time: 2-3 weeks

Features

• Tungsten Carbide Tips brazed in front for high wear resistance.
• Shank made from Alloy Steel 20MnCr5 and case hardened to 50-53 HRc.
• Precision ground. Tip runout within 0.015 mm w.r.t. M. Taper.
• Broadly confirms to DIN : 807

Additional Information:

• Delivery Time: 2-3 Weeks

Features

• Below is the list of carbide tipped dead centers that could be made to order.
• Since these are made against order the delivery could take about 10-12 weeks of time minimum normally.
• Note that special sized carbide tips have to be made in a minimum quantity of 4-6 pieces.
• The below listed sizes of carbide tips have been standardized by us and hence can be ordered by you for even 1 piece. Any other special size ordered outside the below list of sizes has to be ordered for a minimum quantity of 4-5 nos.

Special Carbide Tip Dead Center Specifications - Standard Edition

Content

Special Carbide Tip Dead Center Specifications - Non Stardard Edition

Content

• Made from stainless steel.
• Useful for holding purpose on wire cut machine.
• Suitable for mounting on machine bed.
• Suitable for round job.
• Hardness 55± 3 Rc.
• Accuracy within 15 micron.

Vertical Grinder

To be mounted on the rear tool post side. (On the back of cross slide top ???" BSW threads and bolt the vertical tool post grinder to the cross slide. Mounting Stud provided with the grinder.)

Standard Accessories

• Tool Post Grinder is delivered complete with sturdy guards, motor / spindle pulleys, belts and grinding wheel.
• Electric motor supplied only against request at extra cost.

Precautions

Rotate the external spindle only in the direction indicated by the arrow. Horizontal models of Tool Post Grinders are required to be mounted between job / work piece and operator. Vertical modesl of Tool Post Grinders can be mounted beyond the job / work piece.

 

Electric Motor supplied only against request at extra cost

External Grinder Horizontal Model

To be mounted on lathe tool post. The center of the tool post has to be matched with the center of the lathe. Use a round C.I. / M.S. washer and machine the faces to match the heights.

Applications

For use on Lathes, Shapers, Planer Machines, etc. for operations like Cylindrical External & Internal Grinding, Face / Radius / Surface Grinding.

Spindle

Made from alloy steel suitably heat treated and precision ground. Precision preloaded bearings used.

Standard Accessories

• Tool Post Grinder is delivered complete with sturdy guards, motor / spindle pulleys, belts and grinding wheel.
• Electric motor supplied only against request at extra cost.
• External Grinder Price includes the cast iron mounting body whereas the internal grinding attachment price does not include the cast iron body.

Precautions

Rotate the external spindle only in the direction indicated by the arrow. Horizontal models of Tool Post Grinders are required to be mounted between job / work piece and operator. Vertical modesl of Tool Post Grinders can be mounted beyond the job / work piece.

Keyway Milling Attachment

The keyway milling attachment can be used to mill keyways on shafts mounted between centers on a lathe. The Attachment is mounted on the lathe tool post and the end mill on the ¾" Drill Chuck. The attachment is supplied without electric motor. The Motor Pulley and the Spindle pulley are supplied along with the attachment.

This attachment can also be used to mill or drill holes or slots on jobs mounted on a lathe chuck keeping the lathe chuck stationary.

Motor : Use 0.5 HP 3 Phase 1440 rpm Electric motor.

Spindle Speed: 570 & 1080 rpm

Features

• Small size Taper upto MT-4 made from Bearing Steel EN-31 and through hardened to 58-60 HRc.
• Big size tapers from MT-5 upwards made from 20MnCr5 and Case Hardened to 58-60 HRc.
• Broadly confirms to IS : 2289 - 1976 (Equivalent to DIN: 806-1961 / ISO : 298)
• Precision ground.
• Tip runout within 0.015 mm w.r.t. Taper.
• Standard Point Angle 60° (other Angles like 75° / 90° etc. against request)

Additional Information:

• Delivery Time: 2-3 Weeks

Features

• Small sizeTaper upto MT-4 made from Bearing steel EN-31 and through hardened to 58-60 HRc.
• Big size tapers from MT-5 upwards made from 20MnCr5 and Case Hardened to 58-60 HRc.
• Broadly confirms to DIN: 807
• Precision ground. Tip round within 0.015 mm w.r.t. M. Taper.
• Application: On CNC Lathes with Live Tail Stock. Draw off Nut to be used to remove/extract the dead center from the Tailstock.
• Standard Point Angle 60°.

• Shank Taper	L mm	L1 mm	L2 mm	ØD mm	ØD1 mm	Ød mm	M (Thread)	A/F mm	S/F mm
  MT - 2	64.0	48.0	52	18.0	17.780	8	M22 X 1.5	14	15
  MT - 3	81.0	57.0	67	24.1	23.825	11	M27 X 1.5	19	21
  MT - 4	102.5	72.5	83.5	31.6	31.267	14	M36 X 1.5	27	28
  MT - 5	129.5	87.5	107.0	44.7	44.399	18	M48 X 1.5	36	40
  MT - 6	182.0	108.0	145.0	63.8	63.348	20	M68 X 1.5	55	55

Additional Information:

• Delivery Time: 2-3 Weeks

Features

• Manufacturing against Order only.
• Below is the list of carbide tipped dead centers that could be made to order.
• Since these are made against order, the delivery could take about 10-12 weeks of time minimum normally.
• Note that special sized carbide tips have to be made in a minimum quantity of 4-6 pieces.
• The below listed sizes of carbide tips have been standardized by us and hence can be ordered by you for even 1 piece. Any other special size ordered outside the below list of sizes has to be ordered for a minimum quantity of 4-5 nos.

Additional Information:

• Production Capacity: Manufacturing against Order only.
• Packaging Details: Manufacturing against Order only.

Description
Application: In turning of pipes and tubes which cannot be held by ordinary Live Centers because of small point diameters of live centers.
Not suitable for CNC turning applications.
60 Degree angle Revolving Cone (Not Dead).
Dead Pipe Centers for grinding application (recommended) made against order.
Bearings protected from coolant & dirt/chips by oil seal.

Description
Application: In turning of pipes and tubes which cannot be held by ordinary Live Centers because of small point diameters of live centers.
Not suitable for CNC turning applications. 360 Degree angle Revolving Cone (Not Dead)
Dead Pipe Centers for grinding application (recommended) made against order.
Bearings protected from coolant & dirt / chips by oil seal.

Description
Suitable for CNC Turning.
60 Degree Angle Revolving Cone (Not Dead).
Available as Blunt Type only.
Bearings protected from coolant & dirt / chips by oil seal.

Compound Angle facility.

Used for Precision measurement, setting of angles & Light machining.

Accuracy for Square ness, Flatness & Parallelism within 0.010mm upto 200L & 0.015mm upto 450L.

Angle can be set within ±5 seconds.

Centre Distance between rollers is within 0.005mm.

Made from high quality alloy steel

Hardness 60 ± 2 Rc & Tempered.

Magnetic Table for job holding.

Firm hinged clamp to reduce possibility of distortion.

Magnetic Chuck with fine Pitch. ( 1.5mm )

Types

CNC HD R Model
Interchangeable CNC HD R Model
CNC Medium Duty Small Casing Dia. Models
CNC Medium Duty Slimline Models

Types

Standard
Standard Carbide Tip
Extra Heavy Duty
Super Extra Heavy Duty
Jumbo Heavy Duty Compact Model

Types

ER Collets
E type schaublin collet
E type tail collet 
R8 collet



Made from the best quality spring steel EN-47 &  appropriately Hardened.

Applications

• Made from 20MnCr5 & Case Hardened to 55-58 HRc.
• Precision Ground Internally & Externally.
• Concentricity within 0.015 mm.

Universal Model Turret Sleeve suitable for any make of Turret
Tool Locking for Fig. 1 type of Turret sleeve is by the grub of the Turret Block which locks both the Turret Sleeve as well as the Tool.

Suitable to hold Cylindrical Shank Tools (Eg. Boring Tool Holder) on Turret of CNC Lathe.

Features

• Made from 20MnCr5 & Case Hardened to 55-58 HRc approx.
• Precision ground to an Accuracy of 0.015 mm TIR.
• For best result : Always insist on Trumil make Collets.
• Use C Hook Spanner to avoid breakages.
• Suitable for both Tail & Schaublin type Collets.

ORDRE BY - MODEL No. Eg. Milling Collet Adaptor ISO - 40 E - 40.

TAP SPECIFICATIONS MORSE TAPER SPECIFICATIONS SPLIT SLEEVES FOR DRILL & CENTER DRILLS

Applications

• Made from 20MnCr5. Case hardened to 55-58 HRc.
• As per IS : 6682 - 1982. (Equivalent to DIN : 2187 & ISO : 1080 / 1975).
• Precision ground internally & externally.
• Concentricity within 0.015 mm.

Turret Socket

Turret Socket

Turret Socket